Windsor Range of Stainless Steel Wire Balustrades with Stainless Steel Posts

IF YOU HAVE ANY QUESTIONS ON YOUR WIRE BALUSTRADING, PLEASE CONTACT US ON 01628 526995.

Stainless Steel Posts and fittings are available for Decking in either grade 304 (standard) or marine grade (316). Marine grade should be used within 5 miles of the sea or around swimming pools. Stainless Steel Wire is always marine grade 316.

A single run of up to 25 metres of Stainless Steel Wire may be used when the run is a straight line. A single run may also be used when there are no more than 2 changes of angle, but in this case the maximum run is 15 metres.

The wire can pass through intermediate newel posts, and is joined to the end newel posts by an End Fixing Unit.

Please phone us if the wire length required exceeds any of the maximum lengths .

Normally we recommend 4 wires per balustrade, but note that a wire balustrade will not satisfy Building Regulations as children can climb them.

This Stainless Steel Wire Balustrade with WINDSOR Stainless Steel Posts is only available on level Decking.

In order to make the correct lengths of wire, we will need your requirements for each section.
Please email janmoorhouse@btconnect.com together with a rough sketch of the balustrading.

We will assume that wires are spread evenly over the post, unless you tell us to the contrary.

Stainless Steel Posts and Handrail Units for WINDSOR Balustrade (Unit Price inc. VAT)
Satin Stainless Steel Upright Post welded onto base plate 120mm diameter. Diameter 48.3mm, height 1100mm (this can be shortened if required). Drilled for stainless steel wire. 304 Grade 48.3mm £96.44 316 Marine Grade 48.3mm £114.45	Satin Stainless Steel Cover Plate over Base Plate. Diameter 120mm. 304 Grade 48.3mm £18.08 316 Marine Grade 48.3mm £23.46
Satin Stainless Steel Right Angle Elbow. Diameter 48.3mm. To turn a stainless steel rail through a 90 degree angle. 304 Grade 48.3mm £28.64 316 Marine Grade 48.3mm £37.12	Satin Stainless Steel Tube. Diameter 48.3mm. Maximum length 6000mm. Free cut to length. Price per part or full metre. 304 Grade 48.3mm £44.70 316 Marine Grade 48.3mm £50.75
Satin Stainless Steel Corner Saddle Stem. For use with Iroko Hardwood Handrail (below). 304 Grade 48.3mm £16.77 316 Marine Grade 48.3mm £20.84	Satin Stainless Steel Straight Saddle Stem. For use with Iroko Hardwood Handrail (below). 304 Grade 48.3mm £16.77 316 Marine Grade 48.3mm £20.84
Satin finish Adjustable Elbow. For finishin a step rail at the upright post. 304 Grade £18.08 316 Marine Grade £23.46	Satin Stainless Steel End Cap. Diameter 48.3mm. 304 Grade £7.10 316 Marine Grade £7.75
Satin Stainless Steel Tube Connector. Diameter 48.3mm. 304 Grade 48.3mm £12.21 316 Marine Grade 48.3mm £19.07	Universal Fitting for attaching Stainless Steel Rail. 304 Grade 48.3mm £13.48 316 Marine Grade 48.3mm £17.00
Satin Stainless Steel Wall Socket. Diameter 48.3mm 304 Grade 48.3mm £20.82 316 Marine Grade 48.3mm £24.55	Satin Stainless Steel Elbow. Diameter 48.3mm. For finishing a stainless steel rail at the post. 304 Grade 48.3mm £25.00 316 Marine Grade 48.3mm £32.30
Stainless Steel Cleaner £21.60	Tube of glue for Stainless Steel Tube for 3 joints - £5.10 Tube for 50 joints - £42.65

Stainless Steel Marine Grade Wire and Fixings for WINDSOR balustrade
Satin Stainless Steel End Fixing Units.£17.72 inc. VAT	Marine Grade Stainless Steel 4mm 1x19 Wire. £1.80 per metre inc. VAT
Swageless Unit Replaces the End Fixing Units when the wire goes around more than 2 corners. The product is supplied with fitting instructions. £28.96 inc. VAT	Wire Cutters When using a Swageless Unit, the wire needs to be cut. Pliers are not suitable. £69.83 inc. VAT

Windsor Stainless Steel Wire with Stainless Steel Posts Assembly Instructions

Click for printable version

These assembly instructions only relate to horizontal stainless steel balustrading. We are unable to supply stainless steel balustrading for steps.

1. Erect Stainless Steel Upright Posts.

2. Put Steel Cover Plate over base plate.

3. Attach Saddles/Universal Fittings to pre-drilled rails with self tapping screws (supplied).

4. Assemble and glue rail plus saddles and/or elbows into top of Upright Posts.

5. If the posts have the wire already threaded through the posts, then attach the End Fixing Units to each end newel post and tighten the wires.

6. If the posts do not have the wire already threaded through the posts, then

a) Attach the End Fixing Unit to one external pre drilled end post.

b) Thread the wire through the intermediary posts.

c) Attach the Swageless Unit to the other end (instructions supplied) and cut off the surplus wire.

 

 

Purchase Terms & Delivery
Contact ..
tel 0044 (0)1628 526995 fax 0044 (0)1628 522541
e.sales@haf1.org