Stainless Steel Balustrade with Glass

The WINDSOR Range of Glass Balustrades with Stainless Steel Posts

Stainless Steel Posts and fittings come in two qualities. 304 Grade stainless steel is suitable for most ordinary internal and external uses, and 316 Marine Grade is recommended for outside areas within 5 miles of the sea or around swimming pools. Our WINDSOR Solid Glass Balustrades are available with either a Stainless Steel or hardwood handrail. Windsor balustrades are easy to assemble.

The stainless steel posts and rails are available in either a 42.4mm diameter or 48.3mm. The 42.4mm diameter posts are most suitable for balustrading with a total length under 15 metres. Larger decks should use posts and rails with a 48.3mm diameter. This is recommended both for strength and appearance.

For decks over 600mm from the ground, consult a structural engineer or your local building inspector.

Assembly Instructions for Windsor Glass Balustrades

1. The posts and handrail will be supplied to you pre-drilled. It is therefore necessary to tell us

a) The width of the glass that you require for each section. The width of glass is 4cm less that the distance between the posts. (This allows a 2cm gap between the glass and the post. This gap is required for the glass clamp.)

b) The height of the glass you require for each section. We need to know both the height you require and the distance of the glass from the deck. (This is required so that we can drill the hole in the posts for the clamps, such that if the glass were to slip, it would be supported by the top clamp.)

c) The overall height of the Balustrade. (This will allow us to cut the stainless steel posts to the correct height).

d) The width between the CENTRES of the posts for each section.

e) A sketch of the whole Balustrade. We are unable to supply fittings for glass that over hangs the decking.

PLEASE EITHER FAX THIS INFORMATION on 01628 522 541 or email on jjanmoorhouse@btconnect.com.

This will allow us to quote a price to you, either for the stainless steel alone, or for both the glass and the stainless steel.

2. The glass and the Stainless Steel Posts and Fittings will arrive separately. You should allow around 3 weeks for the receipt of the glass as it is cut to your size and then tempered.

3. When glass and stainless steel has arrived, first erect the Stainless Steel Posts.

4. Remove the lugs from the glass clamps. These lugs are not required unless the glass over hangs the decking. In the event of the glass slipping, it will only slip to the deck level.

5. Assemble the glass and Glass Clamps.

6. Glue and/or screw the rail and supports to the posts.

Stainless Steel Posts and Handrail Units for WINDSOR Balustrade (Unit Price ex. VAT)
Satin Stainless Steel Upright Post welded onto base plate 120mm diameter. Diameter 42.4mm and 48.3mm, height 1000mm. 42.4mm 304 Grade £94.25 316 Marine Grade £101.50 48.3mm 304 Grade £105.00 316 Marine Grade £110.00	Satin Stainless Steel Cover Plate over Base Plate. Diameter 120mm. 304 Grade £9.60 316 Marine Grade £12.80
Satin Stainless Steel Glass Clamps. Available for 8 and 10mm glass with rounded backs. Posts predrilled for these clamps. 304 Grade £14.00 316 Marine Grade £15.40	Satin Stainless Steel End Cap. Diameter 42.4mm. 304 Grade £7.20 316 Marine Grade £9.00
Satin Stainless Steel Right Angle Elbow. Diameter 42.2mm. To turn a stainless steel rail through a 90 degree angle. 304 Grade £18.52 316 Marine Grade £23.18	Satin Stainless Steel Tube. Diameter 42.44mm. Standard length 6000mm. Free cut to length. 304 Grade £25.00 per metre 316 Marine Grade £39.50 per metre
Satin Stainless Steel Corner Saddle Stem. Glued on to post. For use with Iroko Hardwood Handrail (below). 304 Grade £14.00 316 Marine Grade £15.40	Satin Stainless Steel Straight Saddle Stem. Glued onto post. For use with Iroko Hardwood Handrail (below). 304 Grade £14.00 316 Marine Grade £15.40
Iroko Hardwood Handrail with 4 alternative ends. a) Dowelled and pegged for connecting to another handrail. b) Flat end for fitting wall socket. c) Dome End. d) Mitred at end for 90 degree corner. Dia 42.4mm, length 1800mm. End smoothed or turned to fit wall socket. £50.00	Universal Fitting for attaching Stainless Steel Rail. 304 Grade £8.50 316 Marine Grade £10.40
Satin Stainless Steel Tube Connector. Diameter 42.2mm. 304 Grade £7.20 316 Marine Grade £9.00	Satin Stainless Steel Elbow for making a right angle turn of the rail. Diameter 42.4mm. 304 Grade £13.50 316 Marine Grade £18.00
Satin Stainless Steel Wall Socket 304 Grade £10.80 316 Marine Grade £13.00	Tube of glue for Stainless Steel £12.00
Stainless Steel Cleaner £18.00

CARRIAGE
Free carriage on UK mainland orders for stainless steel clamps (ex. Scottish Highlands) for stainless steel products over £75. £7 ex VAT on orders under £75.

8/10mm TEMPERED Glass, polished all round. Prices ex. VAT.

Free carriage on glass but there is an additional carriage charge for non mainland UK, Devon, Cornwall and Scottish Highlands.

TO ADVISE YOU OF THE EXTRA CARRIAGE COSTS PLEASE telephone 01628 526995 or email janmoorhouse@btconntect.com.